Below is a full list of the basic modifications Ken made to the standard MGB in order to create the first Costello MGB V8 in 1970. Most of these changes were later replicated in one way or another by British Leyland. They are listed area by area.

Optional Costello modifications are shown in italics and, since they were available at the time the cars were built, if carried out retrospectively, in our view would not compromise the originality of the vehicle.

Engine Bay

The rear bulkhead and inner front wings were re-profiled to clear the Rover V8 and its specially fabricated tubular exhaust manifolds. Bespoke cast alloy engine mounts.

Steering Column

Modified (by Triumph suppliers Torrington) with the addition of an extra universal joint, also for clearance.

Engine

Buick/Oldsmobile/Rover P6 215 cubic inch V8 in 155bhp tune. Without extra modifications, the available engine configuration at the time necessitated a rather distinctive installation, with a remote centrally-mounted radiator expansion tank and the top hose passing underneath the fan belt. On some blocks, the projection on which the engine number was stamped had to be machined to clear the exhaust manifolds.

Optional modifications were ported and polished cylinder heads, a 'fast road' camshaft and Lumenition contactless ignition.

(In Mk III [1990] specification, a capacity of 3.9 or 4.2 litres was available, together with a standard-fit Costello injection plenum, a K&N air filter, an enlarged throttle body for the larger engine, and a re-mapped ECU)

Sump

Reshaped to clear front cross-member. A cast alloy option was available later.

Cooling

The radiator was enlarged in capacity and moved forward, the ducting panel redesigned with oil cooler installed beneath and a remote oil filter fitted on the right inner front wing. An electric, thermostatically controlled fan was used in place of the belt-driven original.

Inlet Manifold

Mk I cars used the standard Rover P6 configuration inlet manifolds. For the Mk II, this arrangement was superseded by a Costello cast alloy manifold to take two SU HIF-6 carburettors or one rearward-facing 40 DCOE Weber. A Carter/Edelbrock (now Weber 500cfm) carburettor on a matching cast alloy manifold was optional - and was actually standard on a few Buick-engined cars.

Exhaust System

Fabricated tubular 'block hugger' manifolds by Mike the Pipe, modified big bore MGB exhaust pipes and silencers.

Bonnet

Bespoke glass fibre with shaped bulge to clear P6 configuration SU carburettors. Later, Mk II cars did away with the bulge after the introduction of new, lower-profile inlet manifolds.

Transmission

Adapted bell housing, uprated clutch, standard gearbox modified to lock out overdrive in third gear, 3.07:1 final drive ratio (MGC). The Costello five-speed gearbox became optional on later Mk II cars.

Front Suspension

Uprated front anti-roll bar. Uprated lever arm dampers optional. (For Mk III cars, the Costello cast alloy front suspension conversion with tubular dampers had become available)

Rear suspension

Anti-tramp bars, Panhard rod, uprated lever arm or telescopic dampers optional.

Front Brakes

Fitted with high performance Ferodo DS11 pads. A servo was fitted as standard, if not already present. Some later Mk II cars were equipped with optional four-piston Austin Princess or Rover SD1 calipers.

Wheels & Tyres

Standard fit Dunlop 14 x 5J alloys with 165 or 175/70HR x 14 tyres. Cars originally equipped with wire wheels invariably had stronger, Minilite pattern centre-lock wheels fitted instead. 185/60 profile HR rated tyres were a later option, as were 15" wheels (Necessary for clearance with SD1 calipers, depending on the dimensions of the wheels originally fitted).

Cosmetics

Glass fibre bonnet (as above) on the first 50 cars, bespoke aluminium 'eggbox' radiator grille, Costello V8 badge on the rear panel.

Welcome

News

The Costello Story

Costello Gatherings

The Cars

Technical Section

TechTalk with Ken

Articles

Lost Costellos

Gallery

Links

Forum

This ever-expanding section has now been subdivided for ease of navigation. Click on the sub-section you require. Within each of these you will currently find the following topics, listed more or less in chronological order. Some of the subjects arose as a result of your questions to the man himself and can be found in the subsequent Tech Talk With Ken section:

Original Modifications

Technical Section

Text Box: Evolution of the Costello V8
Text Box: MGB - A Brief History
Text Box: Original Modifications
Text Box: Parts & Upgrades
Text Box: Gearboxes
Text Box: Ultimate Costello V8